We are laptop repair specialists!
We have qualified, A+ Certified Technicians ready to diagnose your laptop!
Whether you need a new part, or simply do not know why your laptop is acting up, feel free to give our technicians a call to give you an estimate. MORE
Our A+ Certified Technician will diagnose your laptop completely, and inform you of the problem. Estimated parts and labor to fix it will be given upon completion of testing... MORE
In-plane switching is an LCD technology which aligns the liquid crystal cells in a horizontal direction. In this method, the electrical field is applied through each end of the crystal, but this requires the need for two transistors for each pixel instead of the one needed for a standard thin-film transistor (TFT) display. This results in blocking more transmission area requiring brighter backlights, which consume more power making this type of display undesirable for notebook computers. LCD panels are more likely to have defects than most ICs due to their larger size. In this example, a 12" SVGA LCD has 8 defects and a 6" wafer has only 3 defects. However, 134 of the 137 dies on the wafer will be acceptable, whereas rejection of the LCD panel would be a 0% yield. The standard is much higher now due to fierce competition between manufacturers and improved quality control. An SVGA LCD panel with 4 defective pixels is usually considered defective and customers can request an exchange for a new one. The location of defective pixels is also important. A display with only a few defective pixels may be unacceptable if the defective pixels are near each other. Manufacturers may also relax their replacement criteria when defective pixels are in the center of the viewing area. IPS has since been superseded by S-IPS (Super-IPS), which has all the benefits of IPS technology with the addition of improved pixel refresh timing. Though color reproduction approaches that of CRTs, the contrast ratio remains relatively weak. S-IPS technology only appears in larger displays aimed at professionals, though pricing has come down to the reach of the typical consumer. * LCDs have longer response time than their plasma and CRT counterparts, creating ghosting and mixing when images rapidly change; this caveat however is continually improving as the technology progresses. Reflective LCDs, often found in digital watches and calculators, are illuminated by external light reflected by a (sometimes) diffusing reflector behind the display. This type of LCD can produce darker 'blacks' than the transmissive type since light must pass through the liquid crystal layer twice and thus is attenuated twice, however because the reflected light is also attenuated twice in the translucent parts of the display image contrast is usually poorer than a transmissive display. The absence of a lamp significantly reduces power consumption, allowing for longer battery life in battery-powered devices; small reflective LCDs consume so little power that they can rely on a photovoltaic cell, as often found in pocket calculators. Vertical Alignment displays are a form of LC displays in which the liquid crystal material naturally exists in a horizontal state removing the need for extra transistors (as in IPS). When no voltage is applied the liquid crystal cell, it remains perpendicular to the substrate creating a black display. When voltage is applied, the liquid crystal cells shift to a horizontal position, parallel to the substrate, allowing light to pass through and create a white display. VA liquid crystal displays provide some of the same advantages as IPS panels, particularly an improved viewing angle and improved black level. Normal Liquid Crystal Displays like those found in calculators have direct driven image elements – a voltage can be applied across one segment without interfering with other segments of the display. This is impractical for a large display with a large number of pixels since it would require millions of connections - top and bottom connections for each of red, green and blue of every pixel. To avoid this issue, the pixels are addressed in rows and columns which reduce the connection count from millions to thousands. If all the pixels in one row are driven with a positive voltage and all the pixels in one column are driven with a negative voltage, then the pixel at the intersection has the largest applied voltage and is switched. The problem with this solution is that all the pixels in the same column see a fraction of the applied voltage as do all the pixels in the same row, so although they are not switched completely, they do tend to darken. The solution to the problem is to supply each pixel with its own transistor switch which allows each pixel to be individually controlled. The low leakage current of the transistor also means that the voltage applied to the pixel does not leak away between refreshes to the display image. Each pixel is a small capacitor with a transparent ITO layer at the front, a transparent layer at the back and a layer of insulating liquid crystal between.